Hot Dip Galvanised Steel Bar Grating Panels - ASTM A36 or Q235B

Standard mild steel grating panels 6 m × 1 m

• Dimensions: 6 m × 1 m panels.
• Pitch size: 30 mm × 50 mm.
• Load bearing bars: 30 mm ×3 mm.
• Cross bars: 15 mm × 3 mm.
• Coating: 85 micron hot deep galvanized.
• With fixing clamps all types.

Galvanised grating 6m × 1m section 25 × 5 mm

• Electro forged – wire twist.
• Galva. mesh 30 × 94 notch 70 microns.

Hot dip galvanised steel gratings - B404/41/50SG

• B404/41/50SG open end.
• BB: 40 × 4 mm, CB: 6 mm twisted, mesh: 41.275 × 50 mm.
• Panel: 5850 × 913 mm.
• Serrated.

Hot dip galvanised steel gratings - B355/41/50SG

• B355/41/50SG open end.
• BB: 35 × 5 mm, CB: 6 mm twisted, mesh: 41.275 × 50 mm.
• Panel: 5850 × 913 mm.
• Serrated.

Hot dip galvanised steel gratings - B354/41/50SG

• B354/41/50SG open end.
• BB: 35 × 4 mm, CB: 6 mm twisted, mesh: 41.275 × 50 mm.
• Panel: 5850 × 913 mm.
• Serrated.

Hot dip galvanised steel gratings - B254/41/50SG

• B254/41/50SG open end.
• BB: 25 × 4 mm, CB: 6 mm twisted, mesh: 41.275 × 50 mm.
• Panel: 5850 × 913 mm.
• Serrated.

Grating anti-slippery CS 50 mm × 5 mm 8 mm
Grating, surface anti-slippery (anti-skid), material carbon steel, material standard ASTM A 1011 CS TYPE B, TYPE G2, manufacturing standard ANSI/NAA MM 531, plate dimension (high × thick) 50 mm × 5 mm, grating dimension (width × long) 910 mm × 3050 mm, separation inter plate 30 mm, separation inter bar 50 mm, bar diameter 8 mm, coating galv/cal 600gzn/m², ASTM 123.

G.I grating ASTM A36 600 mm wide × 6 mtr. Long

• Size: 40 × 5 mm thick flat bar (non-serrated type) with standard cross bar.
• Pitch: 30 × 100 mm.
• Grade: ASTM A36.
• Finish: hot dip galvanized at 80 microns.

GI grating 110 mm × 45 mm hole

• Size: 25 mm × 2.50 mm - flat bar thickness.
• Hole Size: 110 mm × 45 mm.
• Standard Width: 900 mm.
• Length: 5950 mm.
• Weight: 68 kgs/Mtr.

Q235 I-bar hot dip galvanised steel grating

• Spec: I-bar grating, size: 508 mm(W) × 995 mm(L), Q235 materials.
• Bearing bar height: 55 mm × 494 mm length.
• Bearing bar pitch: 35.3 mm.
• Bearing bar: 7 mm (top & end) / 4 mm (belly).
• Cross bar 8 mm × 8 mm × 995 mm length, pitch 100 mm center, 5pcs/grating.
• End Plate, flat bar, 7 mm × 55 mm (Height) × 995 mm Length.
• Hot dip galvanizing.
• Packing: bundle/wood pallet.

Hot dip galvanized steel grating serrated to BS 4592

• STM-GSGR-001.
• Hot dip galvanized serrated to BS 4592.
• Size 19 ft × 3 ft, rectangular pattern with hexagonal or square twisted cross bars.
• Size of bearing bars: 40 mm × 5 mm serrated.
• Spacing between bearing bars: 30 mm, connected together with 8 mm hexagonal twisted rod every 100 mm.
• Top surface of bearing bars shall be serrated.
• Grating panels shall be hot dip galvanized of minimum 460 gm/m².
• Grating suitable for max. span 67" for 1/4" deflection under uniform work in load of 6.6 kn/m².
• The grating bar shall be closed end.

Grating bar hot dip galvanized plain surface

• Size: 100cm W × 160 cm L.
• Bar Gratings.
• Plain surface, banded on both ends.
• Flat bar size: 25 mm × 5 mm.
• Load bar spacing: 30 mm.
• Twist road spacing: 100 mm.
• Load bar span: 1600 mm.
• Width: 995 mm.
• Surface treatment: hot dip galvanised.

ASTM A36 galvanized bar gratings open type

• Material: ASTM A36, galvanized open type grating 25 × 5 mm, bearing bars spaced at 30 mm.
• With non-skid cross bars (dia: 9.5 mm) at 100 mm pressure in rectangular pattern.

Hot-dip galvanized ST37 Steel grating

• Bearing bar pitch: 34 mm.
• Cross bar pitch: 34 mm.
• Cross bar thickness: 5 mm.
• Bearing bar thickness: 4 mm.
• Height: 50 mm.
• 6000 mm × 1000 mm grating panels.

Galvanized steel grating, surface anti-slippery (anti-skid)

• Material carbon steel, material standard ASTM A 1011 CS Type B.
• Plate dimension (high × thick) 1-1/4 × 3/16 in.
• Grating dimension (width × long) 36 × 120 in.
• Separation inter plate 1-3/16 in.
• Separation inter bar 4 in, bar diameter 1/4 in.
• Coating galvanized ASTM A123 605gm/m².

Grating, surface smooth, material carbon steel

• Material standard ASTM A 1011 CS type B.
• Manufacturing standard ANSI/NAA MM MBG-531.
• Plate dimension (high × thick) 1 × 3/16 in.
• Grating dimension (width × long) 24 × 120 in.
• Separation inter plate 1-3/16 in.
• Separation inter bar 4 in, bar diameter 1/4 in.
• Coating galvanized, ASTM A 123 605 gm/m².

Grating, material steel grill, type panoramic, sawtooth design

• Plate dimension (high × thick) 25 × 3 mm.
• Grating dimension (width × long) 170 × 247.5 cm.
• Separation inter plate 60 mm, separation inter bar 130 mm.
• Coating galvanized.

Galvanized Steel grating - carbon steel ASTM A36

• Materials: carbon steel ASTM A36.
• Coating: galvanized.
• Horizontal width: 1020 mm.
• Longitude length: 6000 mm.
• Height: 20 mm.
• Thickness: 3 mm.
• Spacing of vertical bar: 30 mm.
• Pacing of cross bar: 60 mm
• Twisted bar diameter: 6 mm.

Hot dip galvanized grating Q235B, 30 × 100 mm mesh

• Material: Q235B.
• Mesh: 30 × 100 mm.
• Bearing bar: 30 × 5.

Heavy Grade galvanised Gratings - 41 × 100 mm mesh

• Hot dip galvanised gratings, heavy grade.
• 30 × 5 mm bearing bar.
• 6 mm square twisted cross bar.
• Mesh: 41 × 100 mm.
• Panel size: 1mtr × 6mtr.
• Material: A36/S 275 JR.
• HDG to BS729 OR BS EN 1461.

Hot dip galvanised gratings, heavy grade - 30 × 50 mm mesh

• 30 × 5 mm bearing bar.
• 6 mm square twisted cross bar.
• Mesh: 30 × 50 mm.
• Panel size: 1mtr × 6mtr.
• Material: A36/S 275 JR.
• HDG to BS729 OR BS EN 1461.

Galvanizing coated grating - 41 × 100 mm mesh

• Size: 6000 mm × 1000 mm.
• Frame bar: 30 × 3 mm.
• Bearing bar: 3 × 3 mm C/C 41 mm.
• Cross bar: 6 mm SQ twisted C/C 100.
• Finish: hot dip galvanizing.

HDG steel grating

• Type G35 × 3/40/50, size 5800 × 1003 with closed ends.
• Type G35 × 3/30/40, size 5800 × 1003 with closed ends.

Grating mild steel hot dip galvanize ASTMA123

• Length = 6000 mm.
• Width = 1000 mm.
• Bearing bar = 25 mm × 3 mm.
• Cross bar = 5-6 mm twisted rod.
• Bearing pitch = 60 mm ( center to center).
• Cross bar pitch = 100 mm ( center to center).
• No serrated surface, mild steel JISG3101, finishing W/hot dip galvanize ASTMA123.

HDG MS Gratings: 2000 mm Long × 500 mm wide

• Main Bar: M. S. Flat – 40 × 5 mm
• Cross Bar: M. S. Flat – 25 × 5 mm
• Spacing between main bars – 30 mm c/c.
• Spacing between cross bars – 100 mm c/c.
• All steel materials shall confirm to A36.